Technical, Mechanical & EngineeringYogyakarta

Control Valves: Operation and Maintenance & Troubleshooting

Jadwal Pelatihan Control Valves: Operation and Maintenance & Troubleshooting

TanggalTempatKota
Belum ada jadwal terbaru

valve

 

25 – 28 Agustus 2014, New Saphir Hotel Yogyakarta

21 – 24 Oktober 2013, Ibis Hotel Yogyakarta

 

To reduce the effect of these load disturbances, sensors and transmitters collect information about the process variable and its relationship to some desired set point. A controller then processes this information and decides what must be done to get the process variable back to where it should be after a load disturbance occurs. When all the measuring, comparing, and calculating are done, some type of final control element must implement the strategy selected by the controller.

The most common final control element in the process control industries is the control valve. The control valve manipulates a flowing fluid, such as gas, steam, water, or chemical compounds, to compensate for the load disturbance and keep the regulated process variable as close as possible to the desired set point.

Many people who talk about control valves or valves are really referring to a control valve assembly. The control valve assembly typically consists of the valve body, the internal trim parts, an actuator to provide the motive power to operate the valve, and a variety of additional valve accessories, which can include positioners, transducers, supply pressure regulators, manual operators, snubbers, or limit switches.

Whether it is called a valve, control valve or a control valve assembly is not as important as recognizing that the control valve is a critical part of the control loop. It is not accurate to say that the control valve is the most important part of the loop. It is useful to think of a control loop as an instrumentation chain. Like any other chain, the whole chain is only as good as its weakest link. It is important to ensure that the control valve is not the weakest link.

Following are definitions for process control, sliding-stem control valve, rotary-shaft control valve, and other control valve functions and characteristics terminology.

 

OBJECTIVE TRAINING :

  1. To able know to introduction to control valves
  2. To able know to control valve performance
  3. To able know to valve and actuator types
  4. To able know to control valve accessories
  5. To able know to control valve selection
  6. To able know to special control valves
  7. To able know to installation and maintenance

 

COURSE OUTLINE

1. Introduction to Control Valves

a. What Is A Control Valve?

b. Process Control Terminology

c. Sliding-Stem Control Valve Terminology

d. Rotary-Shaft Control Valve Terminology

e. Control Valve Functions and Characteristics Terminology

2. Control Valve Performance

a. Dead Band

b. Actuator-Positioner Design

c. Valve Response Time

d. Valve Type And Characterizatione.

e. Valve Sizing

3. Valve and Actuator Types

a. Control Valves

b. Control Valve End Connections

c. Valve Body Bonnets

d. Control Valve Packing

e. Characterization of Cage-Guided Valve Bodies

f. Valve Plug Guiding, Restricted-Capacity Control Valve Trim

g. Actuators

4. Control Valve Accessories

a. Positioners

b. Other Control Valve Accessories

5. Control Valve Selection

a. Valve Body Material

b. Designations for the High Nickel alloys

c. Pressure-Temperature Ratings for Standard Class

d. Face-to-Face Dimensions

e. Control Valve Seat Leakage Classifications

f. Control Valve Flow Characteristics

g. Valve Sizing

h. Non-Destructive Test Procedures

i. Cavitation and Flashing

6. Special Control Valves

a. High Capacity Control Valves

b. Low Flow Control Valves

c. High-Temperature Control Valves

d. Cryogenic Service Valves

e. Customized Characteristics and Noise Abatement Trims

f. Valves Subject to Sulfide Stress Cracking

7. Installation and Maintenance

a. Proper Storage and Protection

b. Proper Installation Techniques

c. Control Valve Maintenance

d. Actuator Diaphragm, Stem Packing

e. Seat Rings

f. Bench Set.

8. Troubleshooting

 

PARTICIPANT

• Instrumentation Engineers & Technicians

• Design and Process Engineers

• Operation, Piping, Mechanical and Plant Engineers

• Maintenance Technician and supervisors

• Service Engineers and supervisors

• Work over engineers and supervisors

• Asset Manager Team members

• Everybody who are responsible for selecting, purchasing, or repairing control valves.

 

TRAINING METHOD

Presentation

Discussion

Case Study

Evaluation

 

FACILITIES

Training Kit

Handout

Certificate

Lunch

2 X Coffee Break

Souvenir

 

 

TRAINING FEE for Control Valves: Operation and Maintenance & Troubleshooting

Rp 9.500.000,- / participant / non residential

(minimal 3 peserta training pasti jalan)

 

Form Pre-Registrasi

Data Materi Training

Topik Training : Control Valves: Operation and Maintenance & Troubleshooting
Link
*Jumlah Peserta Estimasi Jumlah Peserta yang di ajukan
*Nama Peserta Yang Didaftarkan

Personal Data

*Nama
*Jabatan Jabatan/Divisi/Departement
*Nama Perusahaan
*Alamat Perusahaan
*Email Perusahaan
*Email Alternatif eg: gmail, yahoo, hotmail
*Telepon Kantor
Ekstensi
*Handphone
* Harus di isi
Tags
, , ,

Related Articles

Leave a Reply

Your email address will not be published.

Check Also

Close
*Semua Silabus dan jadwal training yang ada di Training SDM adalah milik dari masing-masing vendor penyelenggara training.
Close